Title page for ETD etd-04092003-162026


Type of Document Dissertation
Author Appea, Alexander Kwasi
URN etd-04092003-162026
Title Validation of FWD Testing Results at the Virginia Smart Road: Theoretically and by Instrument Responses
Degree PhD
Department Civil Engineering
Advisory Committee
Advisor Name Title
Al-Qadi, Imadeddin L. Committee Co-Chair
Flintsch, Gerardo W. Committee Co-Chair
Brandon, Thomas L. Committee Member
Collura, John Committee Member
Duke, John C. Jr. Committee Member
Keywords
  • Backcalculation
  • Instrument Response
  • FWD
  • Pavements
Date of Defense 2003-01-24
Availability unrestricted
Abstract
Falling weight deflectometer (FWD) is currently used by most highway agencies to determine the structural condition of the highway network. Utilizing the deflections measured by the FWD, the resilient moduli of layers in the flexible pavement is determined using backcalculation software packages. The moduli can be input into semi-empirical mechanistic equations to estimate the remaining life of the pavement system and aid in informing pavement engineers about timing of maintenance and rehabilitation needs. There have been concerns among practitioners and the research community about the adequacy of the resilient moduli determined by the backcalculation software. Some of the backcalculation models have been simplified and field verification may be needed. Field-measured stresses and strains may be used to quantify the reliability of the backcalculated moduli. The Virginia Smart Road, which has 12 different flexible pavement designs and was built and instrumented with pressure cells, strain gages, thermocouples, frost probes and moisture sensors. To validate the backcalculated moduli theoretically and through instrument response, this research was conducted with following objectives: 1) to determine the resilient moduli of the unbound granular materials on the Virginia Smart Road using small and large plates of the FWD; 2) to investigate the extent of spatial and temporal variability of the FWD deflections among pavement sections; 3) to develop a temperature correction model for the backcalculated HMA resilient moduli; 4) to define an appropriate backcalculation approach and compare the four widely used software approaches; and 5) to correlate backcalculated and laboratory measured moduli. In addition, the FWD measurements were used to establish a comparison between in-situ measured and computed stresses and strains in the pavement. The analytical approaches used are linear elastic, viscoelastic, and viscoelastic combined with nonlinearity. Results show that estimation of unbound granular materials moduli using surface deflections is more reliable when 457-mm-diameter loading plate is used. Analysis of deflections from different sensors showed evidence of spatial and temporal variability. The lowest coefficient of variation of deflections (7%) within sections occurred at low temperatures (2 to 6 °C), while the highest coefficient of variation (42%) occurred at temperatures between 35 to 40 °C. This resulted in the development of a deflection temperature correction model. The model was validated at different temperature ranges. A backcalculation procedure was defined to achieve good root mean square error using four selected software packages. This resulted in the selection of the most reliable software to perform moduli backcalculation. A correlation was established between the nonlinear models produced by backcalculation and laboratory testing of the granular 21-B material. However, for the HMA materials, difference in loading period between laboratory testing and FWD loading pulse could affect the results. The study found that when utilizing the backcalculated moduli, computed strains using viscoelastic modeling were comparable to in-situ measured values. Similarly, calculated stresses compared well with the field-measured stresses; especially at high temperatures. Mix properties, temperature of testing and loading were found to have an effect on the agreement between the measured and computed strains in the wearing surface. The study also recommended further validation of FWD measurements using embedded instruments to calibrate analytical models and further analysis of deflection data so that optimum number of testing points can be determined to limit amount of testing performed for determination of deflection variability.
Files
  Filename       Size       Approximate Download Time (Hours:Minutes:Seconds) 
 
 28.8 Modem   56K Modem   ISDN (64 Kb)   ISDN (128 Kb)   Higher-speed Access 
  Dissertation.pdf 2.79 Mb 00:12:54 00:06:38 00:05:48 00:02:54 00:00:14

Browse All Available ETDs by ( Author | Department )

dla home
etds imagebase journals news ereserve special collections
virgnia tech home contact dla university libraries

If you have questions or technical problems, please Contact DLA.