Title page for ETD etd-07192010-130550


Type of Document Dissertation
Author Navarro, Fernando
Author's Email Address fernav72@vt.edu
URN etd-07192010-130550
Title Cellulose Nanocrystals: Size Characterization and Controlled Deposition by Inkjet Printing
Degree PhD
Department Macromolecular Science and Engineering
Advisory Committee
Advisor Name Title
Roman, Maren Committee Chair
Davis, Richey M. Committee Member
Esker, Alan R. Committee Member
Renneckar, Scott H. Committee Member
Rojas, Orlando J. Committee Member
Keywords
  • Micropatterning
  • Streaming potential
  • XPS
  • Size distribution
  • AFM
  • Cellulose nanocrystals
  • Inkjet printing
  • Particle alignment
Date of Defense 2010-06-29
Availability unrestricted
Abstract
Inkjet printing has generated considerable interest as a technique for the patterning of functional materials in the liquid phase onto a substrate. Despite its high promise, the phenomena associated with inkjet printing remain incompletely understood. This research project investigates inkjet printing of cellulose nanocrystals (CNCs) as a possible method for the fabrication of cellulose micropatterns. CNCs were prepared from wood pulp by H2SO4 hydrolysis and characterized in terms of length, width, and thickness distributions by atomic force microscopy (AFM) and dynamic light scattering. Aqueous CNC suspensions were characterized in terms of shear viscosity with a rheometer. Glass substrates were cleaned with a detergent solution, aqua regia, or a solvent mixture, and characterized in terms of surface chemical composition, surface free energy, polarity, roughness, -potential, and surface charge distribution in air by X-ray photoelectron spectroscopy, contact angle measurements, AFM, streaming potential, and scanning Kelvin probe microscopy (SKPM). Additionally, poly(ethylene glycol)-grafted glass substrates were prepared and characterized in terms of surface free energy, polarity, and roughness. Aqueous CNC suspensions were printed in different patterns onto the different glass substrates with a commercial, piezoelectric drop-on-demand inkjet printer. Inkjet deposited droplet residues and micropatterns were analyzed by AFM, scanning electron microscopy, and polarized-light microscopy. At low CNC concentrations (0.05 wt %), inkjet-deposited droplets formed ring-like residues due to the “coffee drop effect”. The “coffee drop effect” could be suppressed by the use of higher CNC concentrations. The resulting dot-like droplet residues exhibited Maltese cross interference patterns between crossed polarizers, indicating a radial orientation of the birefringent, elongated CNCs in these residues. The observed Maltese cross interference patterns represent unprecedented indirect evidence for a center-to-edge radial flow in drying droplets. The degree of definition of the micropatterns depended strongly on the surface properties of the glass substrates. Well-defined micropatterns were obtained on aqua

regia-cleaned substrates. In addition to the surface free energy and polarity, other factors seemed to play a role in the formation of the inkjet-printed micropatterns. If these factors can be identified and controlled, inkjet deposition of CNCs could become an attractive method for the fabrication of cellulose micropatterns.

Files
  Filename       Size       Approximate Download Time (Hours:Minutes:Seconds) 
 
 28.8 Modem   56K Modem   ISDN (64 Kb)   ISDN (128 Kb)   Higher-speed Access 
  Navarro_F_2010_Copyright.pdf 2.03 Mb 00:09:22 00:04:49 00:04:13 00:02:06 00:00:10
  Navarro_F_D_2010.pdf 20.00 Mb 01:32:35 00:47:36 00:41:39 00:20:49 00:01:46

Browse All Available ETDs by ( Author | Department )

dla home
etds imagebase journals news ereserve special collections
virgnia tech home contact dla university libraries

If you have questions or technical problems, please Contact DLA.