Title page for ETD etd-110399-105241


Type of Document Dissertation
Author Giunta, Rachel K.
Author's Email Address giunta@spinn.net
URN etd-110399-105241
Title Durability of Polyimide/Titanium Adhesive Bonds: An Interphase Investigation
Degree PhD
Department Materials Science and Engineering
Advisory Committee
Advisor Name Title
Kander, Ronald G. Committee Chair
Dillard, David A. Committee Member
Dillard, John G. Committee Member
St. Clair, Terry L. Committee Member
Ward, Thomas C. Committee Member
Keywords
  • Notched Coating Adhesion Test
  • Interphase
  • PETI-5 Adhesive
  • Ti-6Al-4V
  • Pore Penetration
  • Dynamic Mechanical Thermal Analysis
  • Polyimide
  • Aging
  • Degradation
  • Durability
  • Chromic Acid Anodization
Date of Defense 1999-10-18
Availability unrestricted
Abstract
When bonded joints are subjected to harsh environmental conditions, the interphase, the three-dimensional region surrounding the adhesive/substrate interface, becomes critically important. Frequently, failure occurs in this region after adhesively bonded systems are subjected to elevated temperature oxidative aging. In a previous study, this was found to be the case with a polyimide adhesive bonded to chromic acid anodized (CAA) Ti-6Al-4V. The objective of the current research has been twofold: 1) to investigate the effect of thermal aging on the interphase region of polyimide/titanium adhesive joints, and 2) to evaluate the method used in the current study for durability characterization of other adhesive/substrate systems.

The method used in this research has been to characterize the effect of elevated temperature aging on the following systems: 1) Notched coating adhesion (NCA) specimens and 2) bulk samples of dispersed substrate particles in an adhesive matrix. The NCA test has the advantages of an accelerated aging geometry and a mode mix that leads to failure through the interphase, the region of interest. The bulk samples have the advantage of an increased interphase volume and allow for the application of bulk analysis techniques to the interphase, a region that is traditionally limited to surface analysis techniques.

The adhesive systems studied consisted of one of two polyimide adhesives, LaRC™ PETI-5 or Cytec Fiberite™ FM-5, bonded to CAA Ti-6Al-4V. The model filled system consisted of a PETI-5 matrix with amorphous titanium dioxide filler. Through the use of the NCA test, it was determined that bonded specimens made with FM-5 lose approximately 50% of their original fracture energy when aged in air at 177°C for 30 days. This aging temperature is well below the glass transition temperature of the adhesive, 250°C. At the same time, the failure location moves from the anodized oxide layer to the adhesive that is directly adjacent to the substrate surface, the interphase region. Through surface analysis of this region, it is determined that the adhesive penetrates the pores of the CAA surface to a depth of 70 to 100 nm, promoting adhesion at the interface. With aging, the adhesive in the interphase region appears to be weakening, although analysis of the bulk adhesive after aging shows little change. This indicates that adhesive degradation is enhanced in the interphase compared to the bulk.

Analysis of the model filled system gave similar information. Specimens containing titanium dioxide filler had glass transition temperatures that were approximately 20°C lower than the neat polyimide samples. In addition, the filled samples contained a significant portion of low molecular weight extractable material that was not present in the neat specimens.

The tan delta spectra from dynamic mechanical thermal analysis of the filled specimens exhibited a shoulder on the high-temperature side of the glass transition peak. This shoulder is attributed to the glass transition of the interphase, a distinct phase of the polyimide which is constrained by adsorption onto the filler particle surfaces. As a function of aging time at 177° or 204°C, the shoulder decreases substantially in magnitude, which may relate to loss of adhesive strength between the polyimide and the filler particles.

From this research, it has been illustrated that information relating to the durability of adhesively bonded systems is gained using an interfacially debonding adhesive test and a model system of substrate particles dispersed in an adhesive matrix

Files
  Filename       Size       Approximate Download Time (Hours:Minutes:Seconds) 
 
 28.8 Modem   56K Modem   ISDN (64 Kb)   ISDN (128 Kb)   Higher-speed Access 
  etd.pdf 6.70 Mb 00:31:01 00:15:57 00:13:57 00:06:58 00:00:35

Browse All Available ETDs by ( Author | Department )

dla home
etds imagebase journals news ereserve special collections
virgnia tech home contact dla university libraries

If you have questions or technical problems, please Contact DLA.